Application of paste

Paste printing widely used in clothing,fit for a variety of dark-colored material printing, can printing in cotton, linen, viscose, polyester, nylon, polypropylene, vinyl chloride and all kinds of fiber blended fabric. Printing paste coverage is very good, it can make dark clothes printed on any light-colored, and have a certain gloss degree and three-dimensional sense, make clothing looks more upscale. Therefore, printing paste can quickly spread in a short period of time, it’s almost used on every printed T-shirt. Paste and water slurry combination can solve large area printing problem. Paste printing process overcome the water slurry printing limitations, but because of printing paste have a certain hardness, so it’s not suitable for large areas ground pattern, a large area pattern is best to use water slurry to printing, and then embellishment some paste. This can not only solve a large area hard paste problem, but also can highlight the pattern hierarchy. There is also another way to hollowed out a large area of ground pattern, made of rotten effect, but wear always feel a little bit hard, so it’s best to use water slurry and paste combination, to jointly solve the large area printing problem. Analysis advantages and disadvantages about paste printing and dye printing. On the choice about paste printing or dye printing, which in academic and actual production is a long-standing debate problem. According to incomplete statistics, currently used in printing  55% is paste and 45% is a dye. Including 20% is reactive dyes, 20% is disperse dyes, vat dyes and other accounts for 5%. (1) Dye printing will produce more wastewater, paste printing normally don’t wash water, so it will not produce wastewater. (2)Dye printing has a good hand feel and good air permeability advantage, especially in printing large area pattern more prominent. Dye-printed clothes are not only wear comfortable but also less cost. The disadvantage is complex process, many devices, compared with mortar printing simple process and less equipment. On the carcinogenic side, dangerous varieties exist in both dyes and coatings,some paste is actually insoluble in the dye, so both exist  selection problem. (3) In paste printing binder is the key agent, whether in fastness or safety aspect, still far from perfect. In dye printing  the most amount used reactive dyes, in the fixing rate and prevent broken keys also exist more deficiencies, sometimes can’t meet wear requirements.

Read More

The reason pigments affect heat transfer inks viscosity.

Heat transfer ink in heat transfer printing have a key position, ink various properties are very important to product production,among them ink viscosity is more important. Viscosity refers to ink flow fluid in the process,fluid intermolecular interactions will produced hinder molecules relative movement ability measure.It reflects a property of fluid layers in the ink to stop each other flowing and ink itself resistance to flow ability,its essence is ink cohesion (intermolecular binding) strong and weak performance.High viscosity, ink has high cohesion, ink mobility is lower. Affecting viscosity has many factors, including the amount of pigment, oil absorption and fineness, linkers viscosity, fillers. The following introduce the pigment amount, oil absorption and fineness degree to viscosity  extent impact. For the same type of binder, the greater proportion of pigment, the greater force between molecules,ink viscosity is large, but pigment in the ink amount is limited. Oil absorption refers to a certain amount of pigment wetting to form a slurry need to adsorption oil amount (g / 100g),is a description about  pigments and greases binding ability. Under normal circumstances, the higher pigment dispersion, small particles, the pigment is larger than surface area,oil absorption is large, ink viscosity is small, fluidity increased. In addition, oil absorption is related to pigment moisture, oil acidity. Pigments containing more water, oil volume is low; oil acidity increased, pigment oil absorption will be reduced. Ink have a good fineness, indicating that solid particles is very fine, evenly distributed in the ink. Ink fineness depends on bonding material for pigments ect solid particles wetting degree, ink agitation, grinding and other processes handle degree.Bonding material has a strong wetting properties, pigments and solid particles easily wetted, the solid particles easily dispersed, after rolling the ink has a good fineness. Normally, pigments solid particles are present in fine particles flocculated state. Pigment particle size and dispersion state for ink viscosity, adhesion, fluidity and other rheological properties have a certain impact. Pigment particles should be controlled between 0.5-3um, however below 1um pigment particles should be accounted for 80-100%. In the same amount of pigment and filler circumstances, two kinds of solid powder  particles are smaller, the higher dispersion, the more fully wetting in the ink binder, ink viscosity is relatively large, made of circular ink pigment particles compared with other shapes made of ink particles, its viscosity is smaller. transfertagfactory heat transfer ink can choose a lot of pigments, such as fluorescent yellow, lemon yellow, ultramarine, dark blue, silver and so on.

Read More

Tips 丨Hot melt adhesive particles purpose and precautions

Hot melt adhesive is a plasticity adhesive products, hot melt adhesive in a certain temperature range its physical state changes with temperature changes, however the chemical properties is the same, hot melt adhesive particles non-toxic and tasteless, belongs to environmentally friendly glue products,can be used for various industries packaging aspects. So how do we choose the right hot melt adhesive particles? From the color, temperature, operations methods and many other aspects to consider. First we say gule color requirements should be different. Hot melt adhesive on the object appearance treatment not strict than other adhesive, but the objects appearance dust, oil should also be properly handled, in order to make hot melt adhesive particles better display bonding effect. Fast operation is a major feature of hot melt adhesive. Hot melt adhesive work time is generally about 15 seconds, with the modern mode production - assembly line extensive use, for hot melt adhesive working time is require more and more shorter. Another is the anti-temperature, hot melt adhesive is more sensitive to the temperature. When the temperature reaches a certain level hot melt adhesive begins to soften, below a certain temperature, hot melt adhesive will become brittle, so select hot melt adhesive must take full account product located temperature changes. If the temperature is too high, then you can choose high temperature hot melt adhesive. Hot melt adhesives particles are generally used hot melt machine through the heat melting hot melt adhesive, after melting glue is becoming  liquid. Through hot melt hose and hot-melt adhesive gun, delivered to the adhesive appearance,when hot melt adhesive is cooling down,that is, completed the bonding.

Read More

Detailed printing auxiliaries – defoamers

Defoamers are produced by transfertagfactory company have a superior performance,and mainly used for heat transfer printing paste defoamers,with excellent defoaming, and antifoaming effects, which can restrain and eliminate paint application during production, canning and printing process generated bubbles. Defoamers are mainly used for thinner inks.These inks most can be delivered by a pump. During this process, a large amount of air may be mixed and may appear bubbles. In addition, during printing process, these thin ink scraped from the plate or down from the roller, due to impact between the ink, stirring, also produced a large number of bubbles. Aromatic, alcohol, water-based inks all have this phenomenon, while the latter is the most serious, because the latter are mostly alkali-soluble substances, it’s like soap (or detergent) in the water, so foam is very strong . Ink bubbles not only reduce the printed matter quality, but also, seriously ink fountains will produce a large number of bubbles, lead to printing can’t go on. 1）bubbles formation and destruction a brief mechanism. Bubbles, that is, gas into group by the liquid membrane wall surrounded by separation formed .Bubble walls themselves can form very uniform geometries, forming 120 degrees when three bubble walls (films) meet together. At least two or more components can form bubbles (pure liquids can’t foam), because foams require a large amount of surface area, production these surfaces is countered by the liquid surface tension. Therefore, when the liquid surface tension is relatively low, formation a certain amount of stable bubbles required energy is relatively low. When a single-molecule film surfactant-soluble appears on  liquid surface, bubbles will generated. Liquid surface elasticity can also cause bubbles. In general, bubbles is not stable, its destruction is generally due to liquid from bubble wall squeeze into the wall edge to occur it,when membrane wall squeezed to a thickness about 100Ao,molecular motion in the membrane wall is to rupture the bubble structure by destroying liquid membrane. 2）Defoamer function. Defoamers are generally used to eliminate air bubbles through chemical reactions (such as acid or calcium salts can destroy soap film). However, most of defoamers function are spread out on the foam surface, so that surfactant on the bubble before stabilizing effect is removed or replaced,which requires a surface tension smaller than the original bubble-forming film surface tension. If the foam forming agent is easily desorbed and quickly reprocessed, then its effectiveness against defoamers is very small. If the foam desorption function is poor, the surface viscosity is relatively high, the anti-foaming agent spread slowly. A good anti-foaming agent should work very fast. Generally speaking, it should have very low solubility,and have a certain reduce surface tension liquid function.The most effective defoamer chemical structure should be: When it is oriente...

Read More

Precised equipment create high-quality products

As the saying goes, "Good tools are essential things." Good product must be strongly supported by advanced equipment. On the investment of equipment, transfertagfactory always is not stingy. transfertagfactory(Fujian) Heat Transfer co., ltd. has an international standard factory covering more than 30,000 square meters. The production base of this scale is one of the best in heat transfer industry. In order to create a good production environment, our company invested a advanced dust-free workshop, strictly control the temperature and humidity of the workshop. Improve the air flow in the workshop, ensure good indoor air quality, and reduce the noise. Not only provide a comfortable environment for workers, but also provide a clean, safe, environmental protection space. In order to standardize the production and make it professional, the company introduced advanced equipment in home and abroad since 2007. For gravure workshop, transfertagfactory expanded the room of printing workshop, introduced a number of large automatic coating machine and related facilities  the 100-meters coating and casting unit has become a more perfect coating production line. For Screen printing workshop, transfertagfactory introduced 4 KOMORI offset printing machine, 5 SAKURA automatic printing machine and 10 ATMA semi-automatic screen printing machine. In addition, our company also equipped with high precision chemical grinding machine and sewage treatment equipment, not only ensure each production line reach high capacity, focus on environmental protection as well. At present, we have 21 automatic screen printing equipment production lines with a daily production capacity of 385,000 times, which can meet the demand of customers and improve the efficiency, short the lead time. Excellent equipment is the guarantee of product quality. Produce high quality products and make best service is the mission of transfertagfactory. transfertagfactory is really to be your trust and worthy supplier!

Read More

China Manufacturer Of Heat Transfer Sticker

We have more than 20 years history in heat transfer industry , We are specializing in R&D transfers product for professionals partners. We have 3 production department ,3 offset printing machine , 12 semi auto screen printing machine , 7 full auto screen printing machine . So we have huge capacity also the quality and delivery time are in our control. Can help you win more orders ! Heat transfer stikcer is our top 3 selling product, It does not have MOQ, So you can order 1pc for start your business. And simple process, you just need to provide artwork as long as high resolution. Then we can produce for you in any design . Not only save your time but also save your worker cost. And this materail stands out on the playground, on the sidelines, on campus, or anywhere else you'll find fanwear, cheer apparel, Greek letter shirts, and fashion garments. And it is safe for use on children's clothing as well as adult garments.  you'll find the perfect color to impact any project. And when you're ready for a change, it's simple to make a change with this easy-to-use, versatile material. At last but no least , our customers all have their own designs and mostly the artwork owned by them. So we definitely cannot use them , i am sure you understand this . And artwork must be need in AI , PDF or EPS , Not just PICTURE! Because we need to check the price with artwork and use for production we are confident that we have strong experience and can provide you competitive products and price as long as you are willing to partner with us

Read More

Labels without glue outline is originating

In ordinary screen printing and offset printing production, the glue edge is really a phenomenon that seems present. But recently, a purchase from Russia for warmth transfer labels. The customer is really a outfit situated in St. Petersburg city, Russia and supply clothes for a lot of famous branding business for example FILA,puma and so forth. Meanwhile, the needs for brand services are relatively high.The clothing manufacturer offer us high needs in the high elasticity, washing and glue issues.Therefore, we made 3 production plans and enhancements with this sample order. To begin with, to meet up with the interest in versatility, we added 2 processes within the ordinary production plan.At the moment, the elasticity of the label is 2 occasions those of ordinary products.Help make your clothes simple to stretch and excellently rebound. Next, water needs of consumers will also be very strict,our label could be washed greater than 40 occasions once the temperature of water reaches 40 levels. Finally, no halo issue,we've created the samples for 3 occasions.Within the glue process, further enhancements happen to be designed to meet the requirements without glue edge labels.Your clothes could be more upscale with this no halo labels. Product technical information: Whether ecological protection: eco-friendly PU material Transfer temperature: 150-160 Press time: 20-21S Textile care: washing temperature 40-60 levels Washing occasions: greater than 40 occasions / reverse machine wash Tearing method: cold peel / hot peel Wonderful situations are worth awaiting, we're also constantly improving, constantly upgrade. We've been on the path to create a progress. For those who have similar needs, please get in touch.

Read More

New star in the heat transfer industry

Since the beginning of this year, more and more branded apparel has appeared in new styles.Use embroidery patch to embellish clothing.The Embroidery Patch is also known as the embroidery chapter label，belong to high grade label category.Smooth edging/locking, good surface smoothness and full of 3D effect are synonymous with it. Product technical information: press time: 20s heat transfer temperature: 150 ℃-160℃ the use of pressure: 0.5pa Washing standard: 60 ℃ normal temperature, 5 times, 45 minutes / time product instructions,divided into the following two methods. Ironing method: Clean the glue-based parts , place the Embroidery Patch on the appropriate part of cloth, attach the glue side match the clothes, and then spread a silicone paper on Embroidery Patch. Adjust the hot press to 150 ℃. After the temperature is reached, press it directly for 20s in the position of the cloth and Embroidery Patch. Wait for five minutes and ensure it’s cool. If can not reach the Ideal adhesive strength，The above procedure needs to be repeated. Noted: Do not try to remove the Embroidery Patch when its hot. Sewing method: Use the sewing machine to make a circle on the edge of the Embroidery Patch . It is recommended to use the same color as the label. Advantages of the latest Embroidery Patch: Embroidery Patch is different from traditional embroidery, it is easier to match the clothing,the finished garment can also be pasted with embroidery to achieve high quality. There is no longer the MOQ ,complex process ,production speed, high prices, clothing processing single troubles and so on. Embroidery Patch with adhesive backing can be directly applied to textiles, bags, shoes and other textiles. After washing will not fall off, no need Sewing process, saving time and labor cost. In general, this is a new up-star in the apparel industry and Very popular in European and American. Want your clothes to be more outstanding? Let's creates together!

Read More